Diamond Fc7312 Manual de instrucciones

Instruction ManualImportant: Read this instruction manual carefully before putting the Fast-Cut into operation and strictly observe the safety regulat

10In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water. DIAMOND offers the right accessories for all wet cutting ap

11Maintenance- Before performing maintenance work switch off the Fast-Cut (27) and pull out the plug cap.- Allow the Fast-Cut to cool off before do

12Technical dataDisplacement cu in (cm3) 4.5 (73) 4.5 (73) Bore in (mm) 1.97 (50) 1.97 (50)Stroke in (mm) 1.46 (37) 1.46 (37) M

13Denomination of components (Illustration shows model FC7314) 1 Handle 2 Filter cover for air lter and spark plug cap 3 Cover lock 4 Tubular

14Place the spring washer (8) on the arbour and insert the screw (9) and tighten by hand.Turn the disc slowly until the stop hole of the V-belt pulley

15NOTE: The two fastening nuts (11) must be loosened before tightening the V-belt or checking the tension.To increase the belt tension, turn the tight

16FuelsCaution:This tool uses petroleum products (gasoline and oil). Be especially careful when handling gasoline.Do not smoke. Do not allow gasoline

17RefuellingIMPORTANT:FOLLOW THE SAFETY PRECAUTIONS!Be careful and cautious when handling fuels.The engine must be turned off and cooled down!Carefull

18Starting the engineThis model is tted with a semiautomatic decompression valve (1) to make starting easier. Press the rubber cover until you c

19Stopping the enginePush the combination switch (6) down to position .6Warm starting:As described above for cold starting, but before sta

2EMISSIONS COMPONENT DEFECT WARRANTY COVERAGEDiamond Products, 333 Prospect Street, Elyria, OH 44035, (herein “Diamond Products”) warrant(“s”) to the

20Adjusting the carburetorNOTE: The grinding parts are equipped with an electronic ignition to limit the speed. At the factory the idlin

21MAINTENANCECAUTION: Before doing any work on the Fast-Cut turn off the engine, remove the cutting disc, pull the plug cap off the spark plug and wea

22Cleaning the protection hoodOver time, the inside of the protective hood can become caked with material residue (especially from wet cutting),

23Pre-lter (foam with air‑lter oil)Only for models SC-8116XLClean or replace (when cutting with high dust amounts):• Daily or at least every • 4

24Checking the ignition sparkInsert the combination tool (9) between the ventilation hood and cylinder only as shown in the illustration.CAUTION!Do no

25Replacing the starter cableRemove four screws (14). Remove starter housing (15).Insert a small screwdriver through the cooling slits on the back of

261542Replacing the return springRemove the starter housing (see “Replacing the starter cable”).Take the air guide off the starter housing

27Cutting attachment in central / side positionNOTE: The Fast-Cut is delivered with the cutting attachment mounted in the middle position (1).

28Press the cutting attachment (13) onto the drive arm in the side position.Guide the V‑belt (14) over the V-belt pulley (15).NOTE: The ill

29Instructions for periodic maintenanceTo ensure long life, prevent damage and ensure the full functioning of the safety features the following mainte

3Thank you for purchasing Diamond Products!Congratulations on choosing a Diamond Products Fast-Cut cutoff saw! We are condent that you will be satis

30GuaranteeDiamond Products guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting

31Notes

32333 Prospect StreetELYRIA, OHIO 44035(800) 323-5336http://www.diamondproducts.comForm: 995 703 865 (2012‑03 GB)WARNING!Some dust created by power sa

4Delivery inventory1. Fast-Cut2. Adapter ring 0.8"/1.0" (not in the general scope of delivery. Country‑specic)3. Screwdriver (for carbur

52314SAFETY PRECAUTIONSIntended useFast-CutUse the Fast-Cut cutoff saw outdoors only, for trimming and cutting suitable materials, using cutting discs

6- Always wear safety shoes or boots (G) with steel toes, non‑skid soles, and leg protectors when working with the Fast-Cut. Safety shoes equipped wi

7Cutoff discs- The protection hood must always be on! Change discs only with the engine off!- There are two basic types of cutoff discs: - For meta

8Kickback and lock-in- When working with the Fast-Cut there is a danger of kickback and lock-in.- Kickback occurs when the top of the cutting disc i

9When using synthetic resin cutting discs, always ob-serve the following:CAUTION: - Synthetic resin cutting discs can absorb moisture.